BinderMint

How do you set up a Michi method Pokemon binder?

By Al Davies · Updated

Short answer: A Michi method binder treats a page, or a pair of facing pages, as one picture. You mix cards, art panels and empty pockets so the art runs across several pockets. Pick side-loading pages, plan the spread on paper, then fill the pockets.

What is the Michi method?

The Michi method is a way to lay out a Pokemon binder so that a page looks like a display, not a grid of identical cards. Collectors who use it print or cut art panels the size of one or more pockets, and put them between cards.

The plan has three parts: cards, art panels that cover two or more pockets, and pockets left empty on purpose. The empty pockets give the page room to breathe.

Which binder works best for the Michi method?

Choose a side-loading binder. Its pockets open on the side, so a panel that covers two pockets does not slip out when you turn the page. See how side-loading and top-loading pages differ.

A 12-pocket page gives you more room to work with. Each page is 4 pockets wide and 3 tall, so a facing pair is 8 wide and 3 tall. A 9-pocket pair is 6 wide and 3 tall. For totals, read what a full 12-pocket binder holds.

Binder pagePockets per pagePockets across a facing pairPockets in a pair
9-pocket3 wide x 3 tall6 wide x 3 tall18
12-pocket4 wide x 3 tall8 wide x 3 tall24

How do you plan a spread?

Plan on paper before any card goes into a pocket. A spread is small enough to sketch in a minute.

  1. Pick the theme: one Pokemon, one set, one artist or one color.
  2. Draw a grid of 24 boxes for a 12-pocket pair, or 18 for a 9-pocket pair.
  3. Pick 1 or 2 anchor cards and mark their boxes.
  4. Mark the boxes where an art panel covers 2 or 4 pockets.
  5. Mark 2 to 4 boxes to leave empty.
  6. Fill the remaining boxes with cards that fit the theme.

What sizes do art panels need?

A 12-pocket facing pairDiagram of an 8-by-3 pocket facing pair showing one anchor card, a 2-pocket panel, a 4-pocket panel and 3 empty pocketsA 12-pocket facing pairA2-pocket4-pocketgap between pagesA = anchor card. Dashed boxes = empty on purpose.
Spread: One spread can mix single cards, art panels and empty pockets.

A standard Pokemon card is 63 mm by 88 mm, which is about 2.5 by 3.5 inches. A panel for one pocket matches that size. A panel for two pockets side by side is twice as wide. Pocket sizes vary by brand, so measure one pocket in your own binder before you print a batch.

Ultra PRO sizes its standard pocket pages for a card that size, so a panel cut to card size slides in.

1 pocket: one card width x one card height
2 pockets side by side: two card widths x one card height
2 pockets stacked: one card width x two card heights
4 pockets (2 x 2): two card widths x two card heights

Can you use a 9-pocket binder?

Yes. A 9-pocket binder works, with fewer pockets to spread art across. A 3 by 3 page fits one anchor card in the middle with art panels around it. Nine-pocket totals are in a separate guide. A top-loading binder can work, but panels that span pockets may not sit as neatly.

How do you keep the plan and the collection in sync?

A themed binder moves cards out of set order, so a missing card is harder to spot. Keep a list of which card sits on which page and pocket. On a 9-pocket page, one BinderMint photo lists the cards on that page, so you can check a page again after you rearrange it.

Slide each card into a penny sleeve first. Here is when sleeves and toploaders pay off. A binder in set order needs a different page plan.

Tip: Write the spread number in pencil on the first page, so you can find a card by theme.

Last checked 10 November 2026.

Sources

Related